Remotec ZXT-120 V0.5 Uživatelský manuál

1 ZXT-120 (Z-Wave-to-AC IR Extender) Firmware Version: V05

10 are used - extend the battery life by disabling the Surround IR Emitters 33 (0x21) AC function “SWING” control 0x00: SWING OFF 0x01: SWING AUTO(

11 button 3 times within 3 seconds (ZXT-120 set in FLiRS mode) OR • LED flashes four times then stay off (ZXT-120 set in Always Listening mode)

12 2 Place the ZXT-120 and your device remote as shown below, aimed at each other 1-3 inches apart.- 3 Press and keep holding the key on your origin

13 Reset ZXT-120 to factory default Press and hold “PROG” button for 10seconds on ZXT-120. The LED will flash twice until reset process is complete

14 INSTALLATION MOUNTING THE ZXT-120 TO A WALL MOUNTING LOCATION PRECAUTIONS • Before mounting, check the material and structure of the mounting l

15 1. Obtain two screws suitable for the wall strength and material. The screw size is shown in the figure below. 2. The positional relationship

16 5. When removing the ZXT-120 from the wall, lift up the ZXT-120, then pull it towards you. 6. Detach the main unit from the battery chassis by

17 WIRELESS INFORMATION Wireless range: This device has an open-air line-of-sight transmission distance of 100 feet which complies with the Z-Wave s

18 Q Can I use the USB port to configure ZXT-120? A No, the mini USB port only provides an alternative option for user to power the ZXT-120. Q

19 Q Where can I keep up to date with the latest Z-Wave products for my house? A You can keep up to date by visiting the www.remotec.com.hk webs

2 Table of Contents Introduction... 3 Controller and Gateway Requirements ... 4 Built-in I

20 Supported function in Thermostat Command Class Z-Wave command class Description Supported Auto/Auto Low YES Low YES Auto High YES High YES

21 Energy Save Heat NO Energy Save Cool NO AWAY NO ZXT-120 functions and Parameters summaries: FUNCTIONS AIR CONDITIONER FUNCTION Z-WAVE COMMAND

22 COMMAND_CLASS_THERMOSTAT_FAN_MODE, v2 THERMOSTAT_FAN_MODE_SET FAN MODE = 5 COMMAND_CLASS_THERMOSTAT_FAN_MODE, v1 THERMOSTAT_FAN_MODE_SET FAN MODE

23 VERSION COMMAND_CLASS_VERSION VERSION_GET MANUF'ER SPECIFIC COMMAND_CLASS_MANUFACTURER_SPECIFIC MANUFACTURER_SPECIFIC_GET TEMPE

24 CHECKING ACCESSORIES After opening the cover of the packing box, check that the following accessories are included. • ZXT-120 (Z-Wave-to-AC IR

3 Z-ExtenderTM ZXT-120 (Z-Wave-to-AC IR Extender) Operating Instructions Introduction The ZXT-120 is a Z-Wave to air-conditioner (AC) IR Exten

4 ZXT-120 into their Z-Wave network using the primary controller. Then, the user can use either the primary controller or secondary controller to co

5 Glossary Device or Node Devices and nodes are all terms to describe an individual Z-Wave device. These are all interchangeable when setting up yo

6 ZXT-120 Operations Before using the ZXT-120, please read the [INSTALLATION] if it is needed to mount the ZXT-120 to a wall. Power up the ZXT-120

7 Product Overview Figure 2 PROG Key and IR Port of ZXT-120 Temperature sensor “PROG” Button, Learning and LED

8 Z-Wave Remote Control 1) Select your operation mode; please refer to “Listening Mode” section. 2) Include or Exclude the unit from the existing

9 ZXT-120 Information How to get the NIF “Node Information Frame” on ZXT-120 Step Setup Key LED Indication Status on ZXT-120 1 Press the PROG butt